SP-45001M-CXP4

SP-45001M-CXP4

45 MPixel Monochrome CoaXpress Camera

  • 8192 x 5460 Pixels

  • Small 3.2 μm Square Pixels

  • Up to 38 fps at full resolution

  • CoaXPress-4-Lanes (PoCXP)

$ 6,859.00

SPECIFICATIONS

Model SP-45001M-CXP4
Product Family Spark Series
Interface CXP-6 CoaXPress-4-Lanes (PoCXP)
Image Sensor OnSemi XSG 45000
Horizontal Pixels 8,192
Vertical Pixels 5,460
Total Pixels 45 MegaPixels
Frame Rate 38 f/s
COLOR or Monochrome Monochrome
Spectral Range Visible + NIR
Optics Format 35mm Full Frame
Image Sensor PhotoActive Diagonal 31.503 mm
Pixel Size 3.20 μm
Lens Mount F-mount or M42 or M42a
Electronic Shutter Global
Pixel Formats Monochrome: 8/10/12-bits
Frame Synchronization Free-run
Hardware trigger
Software trigger
Digital Inputs 1 Opto-Isolated Input, 1 TTL Input
General Purpose I/O (GPIO) 1 Opto-Isolated Output, 1 TTL Output

ELECTRICAL

Power Input (12-pin Hirose)

PoCXP

+10V to +25V DC. 12.5 W typical @ +12 V
PoCXP Not Supported.
Power Consumption 12.5 Watts

MECHANICAL

Case Type Metal Shielded Box
Case Size (L x W x H) 62 mm x 62 mm x 84.2 mm (excluding connectors)
Mass 330 g
Vibration Tolerance 10 G (20 Hz to 200 Hz XYZ directions)
Shock Tolerance 80 G

STANDARDS COMPLIANCE

REGULATIONS CE (EN61000-6-2, EN61000-6-3),  FCC Part 15 Class B, RoHS/WEEE

ENVIRONMENTAL

Operating Temperature -5°C to +45°C
Storage Temperature -25°C to +60°C
Humidity 20% – 80% non-condensing

 

OVERVIEW

The SP-45001M-CXP4 provides the same 44.7-megapixel monochrome resolution as the SP-45000M-CXP4 but uses a reduced-speed version of the OnSemi XGS 45000 CMOS imager. This results in a list price that is more than 20 percent lower for customers not needing the ultra high performance of the full speed models. It offers the same high image quality and special functions of the higher-speed models, making it well suited to a wide range of high resolution applications.

Significant cost savings for moderate speed applications

With a maximum full resolution frame rate of 38 fps for 8-bit images and 32 fps for 10-bit or 12-bit images, the SP-45001M-CXP4 provides ample speed to support a wide range of high-resolution applications where ultra-high performance is not required. The lower price point enables vision system designers to maximize the cost competitiveness of their systems, especially for applications where multiple high-resolution cameras are utilized.

Built-in functions for HDR imaging

With an exceptionally low dark noise rating (<5e-), the SP-45001M-CXP4 boasts 67 dB of standard dynamic range, extendable to 73 dB by built-in linear or knee-point HDR functions for both monochrome and color models.

Frame averaging for reduced shot noise

For applications that demand the highest possible image quality, the SP-45001M-CXP4 features a Frame Integration mode that can average the exposures of up to 8 sequential frames to dramatically reduce the amount of shot noise in the image.

OPTICS

OPTICS PARAMETERS







 Horizontal PhotoActive Area (PAA h) 22.528 mm
Vertical PhotoActive Area (PAA v) 16.896 mm
Diagonal PhotoActive Area (PAA diag) 28.160 mm
Image Sensor Resolution 91 line pairs/mm
F-Mount Flange Distance 46.5 mm

 

I/O Pinout

 

12-pin I/O Connector
HIROSE HR10A-10R-12P(71)

PIN FUNCTION
1 GROUND
2 DC Power Input +10V to +25V
3 GROUND
4 N/C
5 Opto IN 1 ( – )
6 Opto IN 1 (+ )
7 Opto OUT 1 ( – )
8 Opto OUT 1 (+ )
9 TTL OUT 1
10 TTL IN 1
11 DC Power Input +10V to +25V
12 GROUND

10-pin I/O Connector
Type 3260-10S3(55) HIROSE or EQUIV.

PIN SIGNAL NOTE
1 TTL Out 2 Line 8
2 NC  
3 TTL In 2 Line 10
4 NC  
5 GND GND
6 Lens Power DC 9 Volts
7 RS-232C Tx For Lens Control
8 RS-232C Tx For Lens Control
9 GND  
10 GND  

DOWNLOADS

SP-45001M-CXP4 DATASHEET
SP-45001M-CXP4 MANUAL
SP-45001M-CXP4 MECHANICAL DRAWING (F-Mount)
SP-45001M-CXP4 MECHANICAL DRAWING (M42-Mount)
SP-45001M-CXP4 MECHANICAL DRAWING (M42A-Mount)
SP-45001M-CXP4 Frame Rate Calculator
Shopping Cart
Scroll to Top