Basler CXP-12 Interface Card 1C

Four-Port CoaXPress CXP-12 frame grabber

  • Four CoaXPress CXP-12 connections: 5,000 MB/s camera bandwidth
  • PCIe 3.0 (Gen 3) x8 bus: 6,700 MB/s bus bandwidth
  • Feature-rich set of 20 digital I/O lines
  • Extensive camera control functions
  • Memento Event Logging Tool

$ 923.00

SPECIFICATIONS

Interface standard(s) CoaXPress 1.0, 1.1, 1.1.1 and 2.0
Connectors Four micro-BNC 75 Ohms (also known as HD-BNC™) CXP-12
Status LEDs One CoaXPress Host connection status LED per connection
Number of cameras Area-scan cameras:
One 1- or 2- or 4-connection camera
Four 1-connection cameras
Line-scan cameras:
One 1- or 2- or 4-connection camera
Maximum aggregated camera data transfer rate 50 Gbit/s (5,000 MB/s)
Supported CXP down-connection speeds 1.25 GT/s (CXP-1), 2.5 GT/s (CXP-2), 3.125 GT/s (CXP-3), 5 GT/s (CXP-5), 6.25 GT/s (CXP-6), 10.0 GT/s (CXP-10), and 12.5 GT/s (CXP-12)
Supported CXP up-connection speeds
  • Low-speed 20.83… Mbps (CXP-1 to CXP-6)
  • Low-speed 41.66… Mbps (CXP-10, CXP-12)
Number of CXP data streams (per camera) 1 data stream per camera
Maximum CXP stream packet size 16,384 bytes
PoCXP (Power over CoaXPress)
  • PoCXP Safe Power:
    • 17 W of 24V DC regulated power per CoaXPress connector
    • PoCXP Device detection and automatic power-on
    • Overload and short-circuit protections
  • On-board 12V to 24V DC/DC converter
  • A +12V power source must be connected to the AUXILIARY POWER INPUT connector using a 6-pin PEG cable
Camera types
  • Area-scan cameras:
    • Grayscale and color (YCbCr, YUV, RGB and Bayer CFA)
    • Single-tap (1X-1Y) progressive-scan
  • Line-scan cameras and contact imaging sensors:
    • Grayscale and color RGB
Camera pixel formats supported Raw, Monochrome, Bayer, RGB, and RGBA (PFNC names):

  • Raw
  • Mono8, Mono10, Mono12, Mono14, Mono16
  • BayerXX8, BayerXX10, BayerXX12, BayerXX14, BayerXX16 where XX = GR, RG, GB, or BG
  • RGB8, RGB10, RGB12, RGB14, RGB16
  • RGBA8, RGBA10, RGBA12, RGBA14, RGBA16
  • YCbCr601_422_8, YCbCr601_422_10
  • YCbCr709_422_8, YCbCr709_422_10
  • YUV422_8, YUV422_10
On-board processing
On-board memory 4 GB
Image data stream processing
  • Unpacking of 10-/12-/14-bit to 16-bit with selectable justification to LSb or MSb
  • Optional swap of R and B components
  • Little endian conversion
Input LUT (Lookup Table) Only available for monochrome cameras:

  • 8 to 8 bits
  • 10 to 8, 10 or 16 bits
  • 12 to 8, 12 or 16 bits
Bayer CFA to RGB decoder
  • ‘1-camera’ firmware variant:
    • 3×3 linear interpolation method
    • 3×3 median-based interpolation method
CustomLogic firmware variants
  • 1-camera, customlogic firmware variant
    • one 1- or 2- or 4-connection area-scan camera
    • 91% DSP, 82% FF, 74% LUT and 56% BRAM resources of the Xilinx Kintex Ultrascale XCKU035 FPGA available for user programming
    • 2GB capacity, 12GB/s bandwidth, shared on-board DRAM memory
Data stream statistics
  • Measurement of:
    • Frame rate (Area-scan only)
    • Line rate
    • Data rate
  • Configurable averaging interval
Event signaling and counting
  • The application software can be notified of the occurrence of various events:
    • Standard event: the EVENT_NEW_BUFFER event notifies the application of newly filled buffers
    • A large set of custom events
  • Custom events sources:
    • I/O Toolbox events
    • Camera and Illumination control events
    • CoaXPress data stream events
    • CoaXPress host interface events
  • Each custom event is associated with a 32-bit counter that counts the number of occurrences
  • The last three 32-bit context data words of the event context data can be configured with event-specific context data:
    • Event-specific data
    • State of all System I/O lines sampled at the event occurrence time
    • Value of any event counter
C2C-Link
Description
  • Accurate synchronization of the trigger and the start-of-exposure of multiple grabber-controlled area-scan cameras.
  • Accurate synchronization of the start-of-cycle, start-of-scan and end-of-scan of multiple grabber-controlled line-scan cameras.
Specification
  • C2C-Link synchronizes cameras connected to:
    • the same card
    • to different cards in the same PC (requires an accessory cable such as the “3303 C2C-Link Ribbon Cable” or a custom-made C2C-Link cable)
    • to different cards in different PCs (requires one “1636 InterPC C2C-Link Adapter” for each PC and one RJ 45 CAT 5 STP straight LAN cable for each adapter but the last one)
  • Maximum distance:
    • 60 cm inside a PC
    • 1200 m cumulated adapter to adapter cable length
  • Maximum trigger rate:
    • 2.5 MHz for configurations using a single PC, or up to 10 PCs and 100 m total C2C-Link cable length
    • 200 kHz for configurations up to 32 PCs and 1200m total C2C-Link cable length
  • Trigger propagation delay from master to slave devices:
    • Less than 10 ns for cameras on the same card or on different cards in the same PC
    • Less than 265 ns for cameras on different cards in different PCs (3 PCs and 40m total C2C-Link cable length)

 

MECHANICAL

Format Standard profile, half length, 8-lane PCI Express card
Cooling method Air cooling, fan-cooled heatsink
Mounting For insertion in a standard height, 8-lane or higher, PCI Express card slot
Connectors
  • ‘A’, ‘B’, ‘C’, ‘D’ on bracket:
    • 4x Micro-BNC female connectors
    • CoaXPress host interface
  • ‘EXTERNAL I/O’ on bracket:
    • 26-pin 3-row high-density female sub-D connector
    • I/O lines and power output
  • ‘INTERNAL I/O 1’ and ‘INTERNAL I/O 2’ on PCB:
    • 2x 26-pin 2-row 0.1″ pitch pin header with shrouding
    • I/O lines and power output
  • ‘I/O EXTENSION’ on PCB:
    • 26-pin 2-row 0.05″ pitch pin header with shrouding
    • I/O extension lines and power output
  • ‘AUXILIARY POWER INPUT’ on module:
    • 6-pin PEG power socket
    • 12 VDC power input for PoCXP camera(s) and I/O power
  • ‘C2C-LINK’ on module:
    • 6-pin 2-row 0.1-in header
    • Card to card link
LED indicators
  • ‘A’, ‘B’, ‘C’, ‘D’ on bracket:
    • Bi-color red/green LEDs
    • CoaXPress Host connector indicator
  • ‘FPGA STATUS LAMP’ on PCB:
    • Bi-color red/green LED
    • FPGA status indicator
  • ‘BOARD STATUS LAMP’ on PCB:
    • Bi-color red/green LED
    • Board status indicator
Switches ‘RECOVERY’ on card PCB:

  • 3-pin 1-row 0.1″ header
  • Firmware emergency recovery
Dimensions L 167.65 mm x H 111.15 mm L 6.6 in x H 4.38 in
Weight 196 g, 6.91 oz

 

ENVIRONMENTAL
Operating ambient air temperature 0 to +55 °C / +32 to +131 °F
Operating ambient air humidity 10 to 90% RH non-condensing
Storage ambient air temperature -20 to +70 °C/ -4 to +158 °F
Storage ambient air humidity 10% to 90% RH non-condensing
Certifications
Electromagnetic – EMC standards
  • European Council EMC Directive 2004/108/EC
  • United States FCC rule 47 CFR 15
EMC – Emission
  • EN 55022:2010 Class B
  • FCC 47 Part 15 Class B
EMC – Immunity
  • EN 55024:2010 Class B
  • EN 61000-4-3
  • EN 61000-4-4
  • EN 61000-4-6
KC Certification Korean Radio Waves Act, Article 58-2, Clause 3
Flammability PCB compliant with UL 94 V-0
RoHS European Union Directive 2015/863 (ROHS3)
REACH European Union Regulation 1907/2006
WEEE Must be disposed of separately from normal household waste and must be recycled according to local regulations

HOST BUS

Standard PCI Express 3.0
Link width
  • 8 lanes
  • 1 lane, 2 lanes or 4 lanes with reduced performance
Link speed
  • 8.0 GT/s (PCIe 3.0)
  • 5.0 GT/s (PCIe 2.0) with reduced performance
Maximum payload size 512 bytes
DMA 32- and 64-bit
Peak delivery bandwidth 7,800 MB/s
Effective (sustained) delivery bandwidth 6,700 MB/s (Host PC motherboard dependent)
Power consumption Typ. 17.1 W (7.3 W @ +3.3V,9.8 W @ +12V), excluding camera and I/O power output

CONTROLS

Area-scan Camera Control
Trigger
  • Precise control of asynchronous reset cameras, with exposure control.
  • Support of camera exposure/readout overlap.
  • Support of external hardware trigger, with optional delay and trigger decimation.
Strobe
  • Accurate control of the strobe position for strobed light sources.
  • Support of early and late strobe pulses.
Line-scan camera control
Scan/page trigger
  • Precise control of start-of-scan and end-of-scan triggers.
  • Support of external hardware trigger, with optional delay.
  • Support of infinite acquisition, without missing line, for web inspection applications.
Line trigger
  • Support for quadrature motion encoders, with programmable noise filters, selection of acquisition direction and backward motion compensation.
  • Rate Converter tool for fine control of the pixel aspect ratio: Rate Conversion Ratio in the range 0.001 to 1000 with an accuracy better than 0.1%.
  • Rate Divider tool
Line strobe
  • Accurate control of the strobe position for strobed light sources.

GPIO

General Purpose Inputs and Outputs
Number of lines 20 I/O lines:

  • 4 differential inputs (DIN)
  • 4 singled-ended TTL inputs/outputs (TTLIO)
  • 8 isolated inputs (IIN)
  • 4 isolated outputs (IOUT)

NOTE: The number of I/O lines can be extended using I/O modules attached to the I/O EXTENSION connector.
Usage
  • Any I/O input lines can be used by any LIN tool of the I/O Toolbox
  • Selected pairs of I/O input lines can be used by any QDC tool of the I/O toolbox to decode A/B signals of a motion encoder
  • The LIN and QDC tools outputs can be further processed by the other tools (DIV, MDV, DEL) of the I/O toolbox to generate any of the following “trigger” events:
    • The “cycle trigger” of the Camera and Illumination controller
    • The “cycle sequence trigger” of the Camera and Illumination controller
    • The “start-of-scan trigger” of the Acquisition Controller (line-scan only)
    • The “end-of-scan trigger” of the Acquisition Controller (line-scan only)
Electrical specifications
  • DIN: High-speed differential inputs compatible with ANSI/EIA/TIA-422/485 differential line drivers and complementary TTL drivers
  • TTLIO: High-speed 5V-compliant TTL inputs or LVTTL outputs, compatible with totem-pole LVTTL, TTL, 5V CMOS drivers or LVTTL, TTL, 3V CMOS receivers
  • IIN: Isolated current-sense inputs with wide voltage input range up to 30V, compatible with totem-pole LVTTL, TTL, 5V CMOS drivers, RS-422 differential line drivers, potential free contacts, solid-state relays and opto-couplers
  • IOUT: Isolated contact outputs compatible with 30V / 100mA loads
Filter control
  • Glitch removal filter available on all System I/O input lines
  • Configurable filter time constants:
    • for DIN and TTLIO lines: 50 ns, 100 ns, 200 ns, 500 ns, 1 µs
    • for IIN lines: 500 ns, 1 µs, 2 µs, 5 µs, 10 µs
Polarity control Yes
Power output Non-isolated, +12V, 1A, with electronic fuse protection
I/O Toolbox tools The I/O Toolbox is a configurable interconnection of tools that generates events (usually triggers) from input lines. The composition of the toolset is product- and firmware-dependent.

  • Line Input tool (LIN): Edge detector delivering events on rising or falling edges of any selected input line.
  • Quadrature Decoder tool (QDC): A composite tool including:
    • A quadrature edge detector delivering events on selected transitions of selected pairs of input lines.
    • An optional backward motion compensator for clean line-scan image acquisition when the motion is unstable.
    • A 32-bit up/down counter for delivering a position value.
  • Divider tool (DIV): to generate an event every nth input events from any I/O toolbox event source.
  • Multiplier/divider tool (MDV): to generate m events every d input events from any I/O toolbox event source.
  • Delay tool (DEL): to delay up to 16 events from one or two I/O toolbox event sources, by a programmable time or number of motion encoder ticks (any QDC events).
  • User Actions Scheduler tool (UAS): to delegate the execution of User Actions at a scheduled time or encoder position. Possible user actions include setting low/high/toggle any bit of the User Output Register or generation of any User Events.
I/O Toolbox composition Determined by the selected firmware variant:

  • 1-camera: 8 LIN, 1 QDC, 1 DIV, 1 MDV, 2 DEL, 1 UAS
  • 1-camera, line-scan: 8 LIN, 1 QDC, 1 DIV, 1 MDV, 2 DEL, 1 UAS
  • 4-camera: 8 LIN, 4 QDC, 4 DIV, 4 MDV, 4 DEL, 1 UAS

SOFTWARE

 

Host PC Operating System
  • Microsoft Windows 10, 8.1, 7 for x86 (32-bit) and x86-64 (64-bit) processor architectures
  • Linux for x86 (32-bit), x86-64 (64-bit) and aarch64 (64-bit) processor architectures
  • macOS for x86-64 (64-bit) processor architecture

Refer to release notes for details
APIs EGrabber class, with C++ and .NET APIs:

  • .NET assembly designed to be used with development environments compatible with .NET frameworks version 4.0 or higher

GenICam GenTL producer libraries compatible with C/C++ compilers:

  • x86 dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of x86 applications
  • x86_64 dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of x86_64 applications
  • aarch64 dynamic library designed to be used with ISO-compliant C/C++ compilers for the development of aarch64 applications

DOWNLOADS

COAXLINK QUAD CXP-12 DATASHEET
egrabber Offline Documentation (167 MB executable ZIP file installs to your start menu)
Updated Software for Wndows, Linux and macOS (link to Euresys Manufacturer Web Site)

 

Shopping Cart
Scroll to Top